Impex SM-4008 Instrukcja Właściciela

NOTE: Please read all instructions carefully before using this product Table of Contents Safety Notice Hardware Pack Assembly Instruction Par

STEP 2 (See Diagram 2) A.) Do not tighten the Nuts and Bolts until instructed to do so. B.) Insert a Guide Rod (#24) into the hole on left Base F

10 STEP 3 (See Diagram 3)

A.) Do not tighten all Nuts and Bolts until instructed to so. B.) Attach the Middle Vertical Frame (#9) under the Rear Top Beam (#6) and onto the Rear

12 STEP 4 (See Diagram 4) A.) Attach the Butterfly Base (#11) to the front of Middle Vertical Frame (#9). Attach the Butterfly Pulley Bracket (#14)

M10 x 2 ½” Carriage Bolts (#88), two Ø ¾” Washers (#107), and two M10 Aircraft Nuts (#110). B.) Attach the Butterfly Stopper (#31) to Butterfly Base.

(#87). Push the Butterfly Arm Foam Roll (#64) to Right Butterfly. Repeat same step to install the Left Butterfly (#12). B.) Insert two Swivel Pulley B

15 STEP 6 (See Diagram 6 & Cable Loop Diagram) A.) Attach one end of 113” Butterfly Cable (#45) to the clip on Left Butterfly (#12). Draw

B.) Attach a Pulley (#62) and two Cable Retainers (#78) to the Bracket. C.) Secure them with one M10 x 2” Allen Bolt (#94), two Ø ¾” Washers (#107),

A.) Attach the two Cross-over Swivel Pulley Brackets (#10) to left and right Upper Side Frame (#7). Secure each Bracket with four M8 x 3/8” Allen Bol

18 DIAGRAM 7-2

TABLE OF CONTENTS BEFORE YOU BEGIN...……………. 1 IMPORTANT SAFETY NOTICES...

19 UPPER CABLE (#47) LOOP DIAGRAM

20 STEP 8 (See Diagram 8 & Cable Loop Diagram)

A.) Attach one end of the 97” Sliding Weight Post Cable (#46) to the Rear Upper Frame (#18). Secure it with one M10 x 2 3/8” Allen Bolt (#118), two Ø

DIAGRAM 8 22

STEP 9 (See Diagram 9) A.) Draw the 152” Lower Cable (#44) through the opening on Foot Plate (#32) to the opening on bottom of Middle Vertical Frame

DIAGRAM 9 24

STEP 10 (See Diagram 10) A.) NOTE: Help of another person is strongly recommended for this step. Place the Lifting Sleeve (#28) in between the two Sa

26

SMITH MACHINE PARTS LIST KEY NO. DESCRIPTION Q’ty 1 Front Left Vertical Frame 1 61 1 ½” Square End Cap 1 2 Front Right Vertical Frame 1 62

MULTI-PURPOSE BENCH HARDWARE PACK NOTE: The following parts are not drawn to scale. Please use your own ruler to measure the size. 28

IMPORTANT SAFETY NOTICE PRECAUTIONS This exercise machine is built for optimum safety. However, certain precautions apply whenever you operate a p

MULTI-PURPOSE BENCH HARDWARE PACK NOTE: The following parts are not drawn to scale. Please use your own ruler to measure the size. 29

MULTI-PURPOSE BENCH ASSEMBLY INSTRUCTION Tools Required for Assembling the Machine: Two Adjustable Wrenches and Allen Wrenches. NOTE: It is strong

STEP 2 (See Diagram 2) A.) Attach the Incline Support (#8) to the middle side holes on the two Backrest Supports (#7). Secure it with one M10 x 6

STEP 3 (See Diagram 3) A.) Place the Backrest Board (#11) onto the Backrest Supports (#7). Secure it with four M8 x 1 5/8” Allen Bolts (#32) and

STEP 4 (See Diagram 4) A.) Attach the Leg Developer (#5) to the open bracket on the Front Post (#2). Secure it with one M10 x 3” Allen Bolt (#29)

33

34 MULTI-PURPOSE BENCH PARTS LIST KEY NO. DESCRIPTION Q’ty 1 Main Frame 1 2 Front Post 1 3 Rear Stabilizer 1 4 Seat Bracket 2 5 Leg Developer 1

SM-4008 WEIGHT RESISTANCE CHART Station Ratio Example Low Pulley 100% 10 lb. plate creates 10 lb. resistance Butterfly (both arms) 100% 10

IMPEX® INC. LIMITED WARRANTY IMPEX Inc. ("IMPEX®") warrants this product to be free from defects in workmanship and material, under normal

The warning labels shown here have been placed on the Rear Base, and Bench Rear Stabilizer. If the labels are missing or illegible, please call cu

NOTE: The following parts are not drawn to scale. Please use your own ruler to measure the size. 4

SMITH MACHINE HARDWARE PACK NOTE: The following parts are not drawn to scale. Please use your own ruler to measure the size. 5

SMITH MACHINE HARDWARE PACK NOTE: The following parts are not drawn to scale. Please use your own ruler to measure the size. 6

SMITH MACHINE HARDWARE PACK 7

SMITH MACHINE ASSEMBLY INSTRUCTION Tools Required Assembling the Machine: Two Adjustable Wrenches and Allen Wrenches. NOTE: It is strongly recommende